Maxim-integrated 73M1822/73M1922 Modem CTL Application Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Maxim-integrated 73M1822/73M1922 Modem CTL Application. Maxim Integrated 73M1822/73M1922 Modem CTL Application User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 21
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Simplifying System Integration
TM
73M1822/73M1922
Modem CTL Application User Guide
December 23, 2009
Rev. 1.0
UG_1x22_056
Zobrazit stránku 0
1 2 3 4 5 6 ... 20 21

Shrnutí obsahu

Strany 1 - 73M1822/73M1922

Simplifying System IntegrationTM 73M1822/73M1922 Modem CTL Application User Guide December 23, 2009 Rev.

Strany 2

73M1822/73M1922 Modem CTL Application User Guide UG_1x22_056 10 Rev. 1.0 2.3.2 Answer Command The answer command manually answers an incoming ca

Strany 3 - Table of Contents

UG_1x22_056 73M1822/73M1922 Modem CTL Application User Guide Rev. 1.0 11 2.5 Dial Commands The dial is the command for managing pulse dial featu

Strany 4 - Figures

73M1822/73M1922 Modem CTL Application User Guide UG_1x22_056 12 Rev. 1.0 2.6 Exit Command The exit command terminates the Modem CTL program. Wh

Strany 5 - 1 Introduction

UG_1x22_056 73M1822/73M1922 Modem CTL Application User Guide Rev. 1.0 13 2.7.2 On-Hook Command The onhook command brings the FXO channel on-hook

Strany 6

73M1822/73M1922 Modem CTL Application User Guide UG_1x22_056 14 Rev. 1.0 2.8.1 IET Setting Command The iet (Interval Event Table) is a table of

Strany 7 - 2 Command Descriptions

UG_1x22_056 73M1822/73M1922 Modem CTL Application User Guide Rev. 1.0 15 2.8.2 Measure Command The measure command is used to initiate or termin

Strany 8

73M1822/73M1922 Modem CTL Application User Guide UG_1x22_056 16 Rev. 1.0 2.9 GPIO Management The Modem CTL provides three commands for managing

Strany 9

UG_1x22_056 73M1822/73M1922 Modem CTL Application User Guide Rev. 1.0 17 2.9.2 GPIO Data Command Using this data command the GPIO pin can be rea

Strany 10 - 2.3.2 Answer Command

73M1822/73M1922 Modem CTL Application User Guide UG_1x22_056 18 Rev. 1.0 2.10 Loopback Management There are six different loopback mode can be

Strany 11

UG_1x22_056 73M1822/73M1922 Modem CTL Application User Guide Rev. 1.0 19 2.11 Billing Tone Filter Commands This command enables or disables the

Strany 12 - 2.7.1 Off-Hook Command

73M1822/73M1922 Modem CTL Application User Guide UG_1x22_056 2 Rev. 1.0 © 2009 Teridian Semiconductor

Strany 13 - 2.7.2 On-Hook Command

73M1822/73M1922 Modem CTL Application User Guide UG_1x22_056 20 Rev. 1.0 3 Related Documentation The following 73M1x22 documents are available f

Strany 14 - 2.8.1 IET Setting Command

UG_1x22_056 73M1822/73M1922 Modem CTL Application User Guide Rev. 1.0 21 Revision History Revision Date Description 1.0 12/23/2009 First public

Strany 15 - 2.8.2 Measure Command

UG_1x22_056 73M1822/73M1922 Modem CTL Application User Guide Rev. 1.0 3 Table of Contents 1 Introduction ...

Strany 16 - 2.9.1 GPIO Config Command

73M1822/73M1922 Modem CTL Application User Guide UG_1x22_056 4 Rev. 1.0 Figures Figure 1: Conceptual Diagram of the Linux Modem CTL Application

Strany 17 - 2.9.3 GPIO Control Command

UG_1x22_056 73M1822/73M1922 Modem CTL Application User Guide Rev. 1.0 5 1 Introduction This document describes the 73M1822/73M1922 Modem CTL App

Strany 18 - 2.10.3 Loopback Get Command

73M1822/73M1922 Modem CTL Application User Guide UG_1x22_056 6 Rev. 1.0 1.2 Modem CTL Command Summary Entering tsc_1x22_app at the command line

Strany 19

UG_1x22_056 73M1822/73M1922 Modem CTL Application User Guide Rev. 1.0 7 2 Command Descriptions This section provides the details of each Modem C

Strany 20 - 4 Contact Information

73M1822/73M1922 Modem CTL Application User Guide UG_1x22_056 8 Rev. 1.0 2.2 1x22 Hardware Register Access The Modem CTL provides access to the 1

Strany 21 - Revision History

UG_1x22_056 73M1822/73M1922 Modem CTL Application User Guide Rev. 1.0 9 2.2.2 Register Write Command The register command can also be used to wr

Komentáře k této Příručce

Žádné komentáře