Maxim-integrated MAX15303 PMBus Command Set Uživatelský manuál Strana 42
- Strana / 52
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
MAX15303 PMBus Command Set User’s Guide
Page 42 of 52
Memory and Storage Commands
STORE_DEFAULT_ALL
Reference:
Standard Command
Lockable:
Yes
Command Code:
0x11
Format:
N/A
Data Bytes:
0
Units:
N/A
Transfer:
Send Byte
Factory Value:
N/A
Description/Notes:
See Section 11.2 of the PMBus Specification Part II.
The MAX15303 includes three banks of nonvolatile (flash memory) storage for most “writable”
PMBus command values, referred to as the USER, DEFAULT, and MAXIM stores. These stores are fully
independent, but identical in structure.
The DEFAULT store is intended to function as a backup of an original equipment manufacturer (OEM)
preferred device configuration. OEMs should save identical configurations to the USER store and the
DEFAULT store, such that the USER store can be refreshed from the DEFAULT store if needed.
The contents of the DEFAULT store are never loaded into working memory unless the
RESTORE_DEFAULT_ALL command is sent.
In general, when the STORE_DEFAULT_ALL command is sent, the existing contents of the DEFAULT
store are erased, and the contents of the working PMBus memory (volatile RAM) are written into the
DEFAULT store. There are exceptions to this behavior, as follows:
OPERATION The OPERATION command is not stored to prevent unintentional
enabling/disabling of the output.
COMP_MODEL The working memory COMP_MODEL data is only stored if the
command has been edited (as recorded by STRAP_DISABLE).
MANUF_CONF The manufacturer flags for password command locking are stored
independently in nonvolatile memory for security.
MANUF_PASSWD The manufacturer security password is always volatile for obvious
reasons.
USER_CONF The user flags for password command locking are stored
independently in nonvolatile memory for security.
USER_PASSWD The user security password is always volatile for obvious reasons.
DEADTIME_GCTRL This command is used to initiate a partial internal edit of the
nonvolatile “Config Page” special-purpose memory bank.
Wait at least 450ms for execution after sending the STORE_DEFAULT_ALL command before sending
additional PMBus commands.
- MAX15303 PMBus Command Set 1
- User’s Guide 1
- Introduction 2
- Table of Contents 2
- OPERATION 6
- ON_OFF_CONFIG 6
- VIN_OFF 7
- VOUT_MODE 9
- VOUT_COMMAND 9
- VOUT_TRIM 10
- VOUT_CAL_OFFSET 10
- VOUT_MAX 10
- VOUT_MARGIN_HIGH 11
- VOUT_MARGIN_LOW 11
- VOUT_TRANSITION_RATE 12
- VOUT_DROOP 12
- FREQUENCY_SWITCH 14
- INTERLEAVE 14
- POWER_GOOD_ON 16
- POWER_GOOD_OFF 16
- TON_DELAY 17
- TON_RISE 17
- TOFF_DELAY 17
- TOFF_FALL 18
- Fault-Related Commands 19
- VOUT_OV_FAULT_RESPONSE 20
- VOUT_UV_FAULT_LIMIT 20
- VOUT_UV_FAULT_RESPONSE 20
- IOUT_OC_FAULT_LIMIT 21
- IOUT_OC_FAULT_RESPONSE 21
- OT_FAULT_LIMIT 22
- OT_FAULT_RESPONSE 23
- OT_WARN_LIMIT 23
- VIN_OV_FAULT_LIMIT 24
- VIN_OV_FAULT_RESPONSE 24
- VIN_UV_FAULT_LIMIT 25
- VIN_UV_FAULT_RESPONSE 25
- Unit Status Commands 27
- STATUS_INPUT 28
- STATUS_TEMPERATURE 28
- STATUS_CML 28
- Telemetry Commands 29
- READ_TEMPERATURE_1 30
- READ_TEMPERATURE_2 30
- READ_DUTY_CYCLE 30
- READ_FREQUENCY 30
- PMB_VALUES 31
- Calibration Commands 33
- EXT_TEMP_CAL 34
- CAPABILITY 35
- PMBUS_REVISION 35
- MFR_MODEL 36
- MFR_REVISION 36
- MFR_LOCATION 36
- MFR_DATE 36
- MFR_SERIAL 37
- IC_DEVICE_ID 37
- IC_DEVICE_REV 37
- Security Commands 38
- MANUF_LOCK 39
- MANUF_PASSWD 39
- USER_CONF 39
- USER_LOCK 40
- USER_PASSWD 40
- SECURITY_LEVEL 41
- Memory and Storage Commands 42
- RESTORE_DEFAULT_ALL 43
- STORE_USER_ALL 43
- RESTORE_USER_ALL 44
- RESTORE_MAXIM_ALL 45
- STRAP_DISABLE 45
- Control Loop Commands 47
- FEEDBACK_EFFORT 48
- LOOP_CONFIG 48
- COMP_MODEL 49
- DEADTIME_GCTRL 49
- Trademarks 51
- Revision History 52
Související produkty a manuály pro Hardware Maxim-integrated MAX15303 PMBus Command Set
Hardware Maxim-integrated EE-Sim Uživatelský manuál
(44 stránky)
(44 stránky)
Hardware Maxim-integrated 73M1866B/73M1966B Infineon TAPI High-Level Driver Uživatelský manuál
(35 stránky)
(35 stránky)
Hardware Maxim-integrated Teridian V.22 bis Linux Softmodem for 73M1822/73M1 Uživatelský manuál
(69 stránky)
(69 stránky)
Hardware Maxim-integrated 73M1822/73M1922 MicroDAA Software Architecture Uživatelský manuál
(10 stránky)
(10 stránky)
Miele KM 2050 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Płyty grzewcze Miele KM 2050.
Dostarczamy 1 pdf podręczników Miele KM 2050 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce